manualshive.com logo in svg

Volvo EC60E, Operator'S Manual, Page: 39 / 342

Share
Download
Volvo EC60E Operator'S Manual Download Page 39

Instrument panel, front

The front instrument panel can be adjusted for

better operator comfort.
NOTE!

Prevent machine damage by taking correct action.

Read thoroughly and understand the instructions in

this section to familiarize yourself with the front

instrument panel before trying to operate the

machine.

NOTE!

The front instrument panel is designed to display

one of the supported languages. Refer to page 

45

for details on how to set the language and the units.

V1134960

Adjustable direction of I-ECU

 

l

5
6

2

3

4

1

FLOW

CLIMATE

V1157500

1000

rpm

1 Central warning light screen

2 Gauge screen

3 Engine speed screen

4 Mode screen

5 CCM (Climate Control Module)

screen

6 Indicator screen

 

 

38

Instrument panels

Instrument panel, front

Summary of Contents for EC60E























































































































































































































































































































































Reviews:

No comments