Volvo EC60E Operator'S Manual Download Page 199

Page: 199 / 342

Bucket, installing

WARNING

Risk of crushing!

Attachments that move unexpectedly can cause

injuries.

Make sure people stay out of the working area when

connecting or disconnecting attachments.
1 Place the machine on firm and level ground.

2 Curl in the attachment quick coupler completely

towards the dipper arm (to release the lock

mechanism).

3 Press down to release the red lock device (A) on

the right attachment quick coupler switch and

then press the switch to position (1) to initiate the

attachment quick coupler.

When the attachment quick coupler is initiated,

the buzzer sounds and the check message and

indicator are displayed on the I-ECU. See page

for more information.

4 Press the left attachment quick coupler switch

for more than 0.7 seconds to open the

attachment quick coupler. The switch is returned

automatically. See page

for more information.

NOTE!

When the attachment quick coupler is open, the

buzzer sounds and the warning message and

indicator are displayed on the I-ECU.

V1159076

V1134968

Attachment quick coupler switch, right

V1140835

Attachment quick coupler switch, left

V1147254

WARNING

Quick coupler unlocked

Warning! Quick coupler unlocked

198

Operating techniques

Attachments, connecting and disconnecting

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 199 / 342

Search results

Summary of Contents for EC60E

Reviews: