manualshive.com logo in svg

Volvo EC60E, Operator'S Manual, Page: 66 / 342

Share
Download
Volvo EC60E Operator'S Manual Download Page 66

5 Select “Select work tool” and then choose

the new tool which is newly created.

Wiper interval : Operator can adjust the wiper

interval of 1st step.

Auto idle time

The basic concept of “Auto idle” is to reduce fuel

consumption. The engine rpm will be lowered

automatically to idle mode, if the Auto idle

button is ON and any of control levers (pedals)

or engine speed control switch are not operated

for a certain time. See page 

86

 for more

information regarding Auto idle button on

keypad.

V1158346

Setup

X3

X3

Select work tool
Adjust tool setting

New

Hammer

Shear

VOLVO

Select work tool

 

V1158347

Setup

Wiper interval

Wiper interval

Set wiper interval:

4 s

 

V1137900

Setup

Auto idle time

Set auto idle time:

5 s

Auto idle time

 

Instrument panels

Display unit

 

65

  

Summary of Contents for EC60E























































































































































































































































































































































Reviews:

No comments