Volvo EC60E Operator'S Manual Download Page 280

Page: 280 / 342

Batteries, charging

WARNING

Risk of serious injury.

Short-circuit, open flames or sparks near a charging

battery could lead to an explosion.

Switch off charge current before disconnecting

charging cable clamps. Never charge a battery near

open flames or sparks. Always charge a battery in

well-ventilated areas.

WARNING

Risk of chemical burns.

The battery electrolyte contains corrosive sulphuric

acid which could cause severe chemical burns.

If electrolyte spilled on your bare skin, remove it

immediately and wash the affected area with soap

and plenty of water. If it gets into your eyes or any

other sensitive body part, rinse with plenty of water

and seek immediate medical attention.
- Always turn off the charging current before the

charging lead clips are removed.

- Ventilate well, especially if the battery is charged

in a confined space.

V1066032

Maintenance

Maintenance service, when required

279

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 280 / 342

Search results

Summary of Contents for EC60E

Reviews: