Volvo EC60E Operator'S Manual Download Page 214

Page: 214 / 342

Disconnecting from an attachment

quick coupler, hydraulic

(optional equipment)

WARNING

Risk of crushing!

Attachments that move unexpectedly can cause

injuries.

Make sure people stay out of the working area when

connecting or disconnecting attachments.
1 Place the machine on firm and level ground.

2 Lower the dozer blade and the boom to the

ground.

3 Curl in the hammer completely towards the

dipper arm (to release the locking mechanism).

4 Press the attachment quick coupler switch to

open the attachment quick coupler (unlock

position). See page

194

for operating of the

attachment quick coupler. When the attachment

quick coupler is being opened, a warning symbol

appears on the display unit, the central warning

lamp lights up and the buzzer sounds (unlock

position).

5 Lower the hammer and curl out to lift up the

attachment quick coupler from the hammer.

6 Place the hammer flat on the ground and unhook

it.

V1114278

Attachment quick coupler, hook off

Operating techniques

Hammer

213

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 214 / 342

Search results

Summary of Contents for EC60E

Reviews: