Volvo EC60E Operator'S Manual Download Page 190

Page: 190 / 342

Working in cold weather

DANGER

Risk of electrical shock.

Personal injury results if a body part comes into

contact with a machine that conducts electric

power.

Disconnect the electrical engine heater before

working on the machine.

WARNING

Risk of frostbite.

Bare skin can freeze stuck to cold metal which could

cause injury.

Use personal protective equipment when handling

cold objects.

WARNING

Risk of crushing injury.

The hydraulic system could respond slowly at low

temperatures and could cause unexpected

machine movements.

Operate carefully until the hydraulic system has

reached operating temperature.
Read the advice for starting, see page

148

Use appropriate fluids for the ambient working

temperatures. (see recommended fluids in

specification section.)

The windows must be free from ice and snow before

putting the machine to work.

Watch out for ice on the machine causing slippery

conditions. Step only onto anti-slip surfaces.

Use an ice scraper on a long handle or a ladder

when removing ice from the windows.

Operating techniques

Working within dangerous areas

189

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 190 / 342

Search results

Summary of Contents for EC60E

Reviews: