Volvo EC60E Operator'S Manual Download Page 305

Page: 305 / 342

Fuel system

Fuel

Fuel quality requirements
The fuel should at least meet the legal requirements, national and international standards

for marketed fuels, for example: EN590 (with nationally adapted temperature

requirements), ASTM D 975 No. 1D and 2D, JIS KK 2204. Fuel specification varies

according to the working temperature. Please contact authorized Volvo dealer.

Sulphur content
According to current USA legal requirement, the sulphur content in the diesel fuel must

not exceed 0.0015 percent (15 ppm) by weight.

According to current EU/other countries legal requirements, the sulphur content in the

diesel fuel must not exceed 0.001 percent (10 ppm) by weight.

Bio-diesel fuel
Vegetable oils and / or esters, also called “bio-diesel”, (e.g. rape-seed methyl ester RME

fuel), which are offered on certain markets both as pure products and as mixed into the

diesel fuel.

Volvo Construction Equipment accepts a maximum intermix of 7% bio-diesel fuel in the

diesel fuel, ready mixed from the oil companies. A higher intermix than 7% of bio-diesel

fuel may cause:

- Increased emission by nitrogen oxide, (thereby not meeting legal requirements)

- Shorter service life of engine and injection system

- Increased fuel consumption

- Altered engine output

- Shortening the engine oil change interval to a half

- Shortened service life of rubber materials in the fuel system

- Less good cold handling properties of the fuel

- Limit storage time for the fuel, which may cause clogging up of the fuel system if the machine is

laid up for longer periods

Warranty condition
The warranty does not cover damage caused be an intermix of more than 7% of bio-diesel

fuel.

304

Specifications

Fuel system

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 305 / 342

Search results

Summary of Contents for EC60E

Reviews: