Volvo EC60E Operator'S Manual Download Page 306

Page: 306 / 342

Alternative fuels

This statement is only valid for Volvo branded

engines, but also includes engines for DD25 and C-

series Skid Steer Loaders where warranty is

provided by Volvo.
Hydro-treated vegetable oil (HVO) and fatty acid

methyl ester (FAME) biodiesel are both made from

renewable raw materials such as vegetable oils and

animal fats, but they are chemically processed in

different ways.
Hydro-treated vegetable oil (HVO)

HVO is created using a chemical process called

hydro-treating. Hydro-treating creates an oxygen-

free hydrocarbon product that is very similar to

distillate diesel fuel and is well suited for use in

diesel engines. HVO that conforms to CEN prEN

15940 is approved for use in all Volvo Construction

Equipment diesel engines with no changes to

maintenance intervals.
Biodiesel

Biodiesel is a product made from renewable

resources such as vegetable oils or animal fat.

Biodiesel that has been chemically processed into

fatty acid methyl ester (FAME) can be blended with

distillate diesel fuel and used in some diesel

engines. Unblended biodiesel is referred to as B100

because it is 100% biodiesel.

Rapeseed methyl ester (RME) is the most common

type of FAME used in Europe. Soy methyl ester

(SME) and sunflower oil methyl ester (SOME) are

the most common types of FAME used in the US.

Although use of FAME biodiesel is now a legal

requirement in some markets, it is not as suitable

for use in diesel engines as conventional diesel fuel

or HVO (hydro-treated vegetable oil).
Biodiesel fuel requirements

The FAME biodiesel blends specified in the table

below are approved for use if:

- The biodiesel is pre-blended by the fuel supplier

- The biodiesel used in the blend conforms to

EN14214 or ASTM D6751

- The distillate fuel used in the blend meets fuel

sulphur requirements

- The distillate fuel used in the blend conforms to

EN590 or ASTM D975

Specifications

Fuel system

305

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 306 / 342

Search results

Summary of Contents for EC60E

Reviews: