manualshive.com logo in svg

Volvo EC60E, Operator'S Manual, Page: 277 / 342

Share
Download
Volvo EC60E Operator'S Manual Download Page 277

Maintenance service, when

required

Engine oil level, checking

See page 

259

.

Fuel, filling

WARNING

Risk of fire.

Burning fuel can cause fatal injuries.

Stop the engine before filling fuel.

WARNING

Risk of fire and explosion.

A running auxiliary heater during fuel filling could

cause fire and explosion.

Switch off the auxiliary heater before filling fuel.
1 Carefully clean around the filler cap on the fuel

tank before removing it.

2 Open the fuel filler cap (A) and fill the fuel in the

tank.

3 Check the fuel level on the I-ECU. See page

38

.

Avoid spilling the fuel when filling, which attracts

dirt. If fuel is spilled, clean it up immediately.

During the cold season, fill up the fuel tank to

prevent water condensing in the tank.

For the capacity of fuel tank, see page 

309

.

V1155536

A

A Fuel filler cap

 

 

276

Maintenance

Maintenance service, when required

Summary of Contents for EC60E























































































































































































































































































































































Reviews:

No comments