manualshive.com logo in svg

Volvo EC60E, Operator'S Manual, Page: 126 / 342

Share
Download
Volvo EC60E Operator'S Manual Download Page 126

Air compressor

(optional equipment)
The air compressor is used primarily to clean the

dust from inside the cab, and the engine air cleaner.

1 Press the air compressor switch to ON position

to operate the compressor, see page 

35

.

NOTE!

When the tank pressure of the compressor is under

6.11 kgf/cm 

2

, the compressor works. However,

when the tank pressure is 8.16 kgf/cm

2

, the

compressor shuts down.
NOTE!

The motor has run over 20 minutes, warning

message is pop up on the I-ECU.
2 Clean out the dust with the air gun.
NOTE!

The air gun is stored inside the cab.

Caution for operation

Never use compressed air for cleaning clothes or

persons.

WARNING

Risk of serious injury.

Compressed air, water jets or steam may cause

damage to unprotected skin and eyes.

Always wear personal protective gloves, goggles

and clothing when using compressed air, water jets

or steam.

Do not touch the surface of compressor while it is

running. The case temperature can reach about

130°C.

Bleed the air in the tank after using the

compressor.

Do not disassemble and modify the compressor.

Do not use the compressor extensively in humid

areas or on rainy days.

V1158626

 

Other controls

Operator comfort

 

125

  

Summary of Contents for EC60E























































































































































































































































































































































Reviews:

No comments