manualshive.com logo in svg

Volvo EC60E, Operator'S Manual, Page: 287 / 342

Share
Download
Volvo EC60E Operator'S Manual Download Page 287

Engine air cleaner secondary filter,

replacing

Replace the secondary filter every 3rd time primary

filter is replaced or at least every 2 years.
If the indicator is still alight even though the primary

filter has been cleaned or replaced, the secondary

filter should be replaced.
The secondary filter (D) works as a protective filter

in case the primary filter (C) should be damaged.
NOTE!

The secondary filter must always be replaced,

never cleaned.
NOTE!

Never remove the secondary filter unless it is to be

replaced.
1 The secondary filter should be removed carefully

and with precision so that no impurities enter the

engine.

2 Carefully check that the new secondary filter is

correctly installed.

NOTICE

Take care of filters, oils and liquids in an

environmentally safe way.

Engine air cleaner cover, cleaning

The cover for aircleaner should be cleaned when

the primary filter is cleaned.

1 Remove the cover (B) and valve (A) from the air

cleaner.

2 Empty and clean the cover and valve.

3 Reinstall them on the air cleaner.

Radiator and coolers, cleaning

See page 

270

.

V1066004

C

D

C Primary filter

D Secondary filter

 

V1066005

A

B

A Vacuator valve

B Cover

 

 

286

Maintenance

Maintenance service, when required

Summary of Contents for EC60E























































































































































































































































































































































Reviews:

No comments