Volvo EC60E Operator'S Manual Download Page 47

Page: 47 / 342

C Initial camera screen (if installed)

All the cameras installed on the machine will be

displayed on the I-ECU. The initial camera

screen is dismissed by pressing the camera

button on the keypad.

NOTE!

Press the camera button on the keypad for the

camera views when operating the machine. For

detailed information about camera control, see

page

135

D Main screen

After the initial camera screen is dismissed, the

main screen is displayed.

NOTE!

Indicator for seat belt will be displayed for 3 seconds

on the "Daily maintenance" screen or main screen.

Fasten the seat belt before operating the machine.

V1170149

CLIM ATE

Flow

F LOW

CLIM ATE

V1158196

1000

rpm

Instrument panels

Display unit

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 47 / 342

Search results

Summary of Contents for EC60E

Reviews: