Volvo EC60E Operator'S Manual Download Page 221

Page: 221 / 342

WARNING

Risk of burns.

Hot oil can cause severe burns to unprotected skin.

Always wear personal protective gloves, goggles

and clothing when handling hot oil.

WARNING

Risk of high pressure injection.

Residual pressure in the hydraulic system could

lead to serious injury. Oil under high pressure can

jet out, even if the engine has not been running for

some time.

Always release the pressure and ensure the ignition

switch is in the off position before you perform any

service of the hydraulic system.

1 Loosen lock nut (B) a bit and turn adjusting

screw (A) counter-clockwise slowly.
NOTE!

Before turning the adjusting screw, mark its

position to facilitate assembling later (setting

pressure : 250 kgf / cm²)
The boom will then slowly be lowered to the

ground.

2 Turn adjusting screw (A) to its original position.

3 Hold adjusting screw (A) securely and tighten

lock nut (B).

4 Contact an authorized Volvo CE dealer

workshop.

V1078568

220

Operating techniques

Hose rupture valves

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 221 / 342

Search results

Summary of Contents for EC60E

Reviews: