Volvo EC60E Operator'S Manual Download Page 73

Page: 73 / 342

Camera screen : See page

135

for more

information.

7 Vehicle messages

This shows the headlines of messages. There

are no errors or warning messages in normal

operation.

If an abnormal condition is sensed, then the

message will display the specific error/failure.

Contact a workshop authorized by Volvo for

advice, if needed.

When pressing the SELECT button to view detail

information about a headline, the displayed

information replaces the whole "main screen".

The information content includes;

- Fault Active

- Error Code

- Source

- First Event

- No. of events

- Last event

V1160717

Setup

Camera screen

Original image

Mirror image

V1137911

Vehicle messages

Engine system

Check at next stop

System failure
(Engine system)

Fault Active: Yes
Error Code: P203A86
Source: ECM
First Event: 20140101
No. Events: 2
Last Event: 20140101

Instrument panels

Display unit

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 73 / 342

Search results

Summary of Contents for EC60E

Reviews: