Volvo EC60E Operator'S Manual Download Page 37

Page: 37 / 342

2 Attachment quick coupler switch, left

This switch has 2 different functions of the

attachment quick coupler according to the

operating condition.

Press down 1: Attachment quick coupler, opening

control

The switch is returned automatically. Press the

switch for more than 0.7 seconds to open the

attachment quick coupler.

When the attachment quick coupler is open, the

buzzer sounds and the warning message and

indicator are displayed on the I-ECU.
NOTE!

The attachment quick coupler switch for initiating on

the right instrument panel must be pressed first to

activate this switch. See page

194

for the

operation.

Press down 1: Attachment quick coupler,

confirming control

When the check message for confirming appears

on the I-ECU, press the switch for more than 0.7

seconds to confirm that the attachment quick

coupler is locked. Then the buzzer sound will be

turned off and the check message and indicator will

disappear.

V1140835

V1147254

WARNING

Quick coupler unlocked

Warning! Quick coupler unlocked

V1147255

CONFIRM QUICK COUPLER

IS LOCK

Confirm quick coupler is locked

Instrument panels

Instrument panel, left

Summary of Contents for EC60E























































































































































































































































































































































Search results

Summary of Contents for EC60E

Reviews:

Volvo EC60E, Operator'S Manual, Page: 37 / 342

Search results

Summary of Contents for EC60E

Reviews: