manualshive.com logo in svg

Vishay VT 200, Technical Manual, Page: 75 / 84

Share
Download
Vishay VT 200 Technical Manual Download Page 75

 

 

Service Operations and Testing 

Testing the Indicator 

 

 

VT200/220 Technical Manual, Rev 1.00.01 

75

 Doc 

# 

TM-VT200/220-EN

 

4.  

Press 

PCS

 ( ) to toggle output 2 on and off. When it is on, the data sent should 

be displayed in the sixth digit. If the output connects to another device, check if 
the signal was received. 

5.  Connect a device to the digital input, and send a signal. See if the data appears in 

the first digit. 

8.2.4 

Testing the Print Buffer (Function 94) 

  To test the print buffer: 

Access the function menu and select function 94. An ASCII file (30h-7Fh) is 
output to the printer port, with error control. 

8.2.5 

Testing Data Received on Both Serial Ports (Function 96) 

  To test data received on one or both serial ports: 

1.  Access the function menu and select function 96. 
2.  The display shows data received on COM ports, as follows: 

 

 

The two digits on the left (first and second digits) show data received on 
COM 1. 

 

 

The two digits on the right (fifth and sixth digits) show data received on  
COM 2. 

3.  Connect a PC or another device to one or both of the indicator’s ports, and begin 

transmitting data. Watch the display to see if the data is received properly. 

Summary of Contents for VT 200





















































































Reviews:

No comments