manualshive.com logo in svg

Vishay VT 200, Technical Manual, Page: 51 / 84

Share
Download
Vishay VT 200 Technical Manual Download Page 51

 

 

Serial Communication 

Output Types 

 

 

VT200/220 Technical Manual, Rev 1.00.01 

51

 Doc 

# 

TM-VT200/220-EN

 

   Continuous Weight Data Block Composition LEO Format 

Byte Name 

Description 

1 

Weight status 

Bit 0: 

0=Normal 

     

Bit 1: 

0=Gross  

      

Bit 2: 

0=No Auto zero        

Bit 3: 

0=Within range     

Bit 4: 

0=No standstill  

Bit 5: 

0=Normal      

Bit 6: 

Must be always set to 1 

Bit 7: 

Zero or parity           

1=No weight display 

1=Net  

1=Auto zero  

1=Out of range  

1=Standstill  

1=Under minimum weighing range 

 

2 Polarity 

“+” 

or 

“-”. 

3-8 

Net weight 

6 digits, including decimal point if any. 

9 

Sync 

Carriage return (0D hex) for end of transmission. 

   Continuous Weight Data Block Composition  AND Format 

Byte Name 

Description 

1-2 

Weight status1 

ST - Weight is stable 

US - Weight is unstable 

OL - Weight is overloaded 

3 

 

Always "," (Comma 2C hex) 

4-5 

Weight status2 

GS - Weight is gross 

NT - Weight is net 

TR -  If regular tare is in system, when pressing P.TARE key, TR will be 
displayed briefly.  

PT - If preset tare is in system, when pressing P.TARE key, PT will be 
displayed briefly. 

6 

 

Always "," (Comma 2C hex) 

7 Polarity 

“+” 

or 

“-” 

8-14 

Weight  

7 digits, including decimal point (2E hex) if any 

15-16 

Weight Unit 

"kg" for kilogram, space (20 hex) +"t" for ton and "lb" for pound.  

17-18 

Sync 

CR+LF - Carriage return (0D hex) and Line feed (0A hex) for end of 
transmission. 

Summary of Contents for VT 200





















































































Reviews:

No comments