Vishay VT 200 Technical Manual Download Page 33

Page: 33 / 84

Display, Keys and Menus

Setup Menus

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

Par. Description

Values

1.t

Auto power off

. Time for the unit to switch off if the scale is zero.

00 - 99 minutes
00=Disabled

1.E

Number of samples in counting

5 - 99

SETUP > SETUP 2 (Com 1 Settings)

Par Description

Values

2.t

Print type.

Selects current print

format from ten default formats and
two custom formats, or disables printer
port.

00=port disabled; 01=ticket; 02=weight output;
03=single line; 04=ticket; 05=ticket; 06=single line;
07=weight; 08=serial and weight; 09=demand;
10=label; 13=alibi memory; 20=custom print formats
(see section

6.5); 22=continuous weight output

w/dual scale

2.c

Master/Slave protocol address.

60-90

2.C

Print-on-demand character.

65-90

2.L

Page length.

Ticket length, in

linefeeds.

2.r

Paper reverse.

Number of reverse

linefeeds before printout.

2.A

Left margin.

Number of spaces from

left margin.

2.F

Page header.

Number of linefeeds

before printout.

2.E

Line termination.

0=LF 1=CRLF 2=LFCR

2.1

Printer model.

0=FANFOLD(like Epson EP-FX or similar serial printer)
1=SLIP(like Epson TM-295)

2.2

Continuous weight output format

LEO or AND

2.3

Print below minimum capacity

0=NO 1=YES

2.4

(Reserved for future use)

2.5

(Reserved for future use)

2.6

Wait unload.

0=NO 1=YES

2.7

Printer error control.

Set to 0 for

communication with a PC.

0=NO 1=YES

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 33 / 84

Search results

Summary of Contents for VT 200

Reviews: