Vishay VT 200 Technical Manual Download Page 45

Page: 45 / 84

General System Parameters

PAR Menu

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

5 General System Parameters

Two of the VT200/220 setup menus provide access to general system parameters,
which affect how the scale operates:

The

PAR

menu contains parameters including the number of display digits, the

position of the decimal point, the A/D gain and the zero range (see chapter

5.1).

The

SETUP 1

submenu, inside the

SETUP

menu, contains parameters including

the date format, totalizer enabling and auto power off (see chapter

5.2).

If you have two scales connected to the indicator, each scale has its own set of

parameters. All the parameters in the menus relate to the currently active

scale. To change parameters for scale 2, for instance, switch to scale 2 by
pressing

SCALE

(

), and then access the menu and change the required

parameters.

Other setup menus allow you to calibrate the scale (

CAL

menu; see chapter

4); set

communication parameters (

SETUP 2

and

SETUP 3

; see chapter

6); and input/output

parameters (

SETUP 4

SETUP 5

and

ACAL

; see chapter

7).

5.1 PAR

Menu

5.1.1

Accessing the Menu and Editing Parameters

To access the PAR menu:

Turn on the unit.

During the self-test routine, while all display segments are on (all 8 on the

display), press

PRINT

( ) momentarily, followed by

TARE

( ) momentarily.

3. If the PIN code is activated, the display shows

ACCESS

briefly. Type the PIN and

press

PRINT

( ) to enter the calibration menu. The display shows

SETUP

4. Use

TOTAL

(

) to scroll to the

PAR

menu.

5. Press

PRINT

( ) to enter the menu.

To edit parameters in the PAR menu:

1. The current parameter number is shown on the display. Use

PRINT

( ) to scroll to

the parameter you need (see the following section for descriptions of parameters).

2. To edit the parameter value, use

P.TARE

(

) to increment the current digit and

TARE

( ) to move to the next digit (if any).

3. When the display is showing the required value, press

PRINT

( ) to confirm your

selection.

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 45 / 84

Search results

Summary of Contents for VT 200

Reviews: