Vishay VT 200 Technical Manual Download Page 34

Page: 34 / 84

Display, Keys and Menus

Setup Menus

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

Par Description

Values

2.8

Operator print type change

(Fn 20-

30).

0=NO 1=YES

2.d

Data bits/Parity serial channel 1

N8 = 8 Data bits/no parity, 07 = 7 Data bits/odd
parity, E7 = 7 Data bits/even parity,

2.11

1 line with date, time and indicated
weight

07-10-03 15:25:20 00500kgG

0=NO 1=YES

2.b

Baud rate serial channel 1.

12= 1200 bps
24= 2400 bps

48 = 4800 bps

96 = 9600 bps

Above

2.2

2.b

and

2.d

settings only suitable to set

2.t

=0.2 for Continuous

Weight Output.

SETUP > SETUP 3 (Com 2 Settings)

Par.

Description

Values

3.t

Instrument communication type.

00=disabled; 01 =continuous weight output;
02=EDP protocol output; 03=printer protocol output;
06=continuous weight w/tare output; 11=continuous
output with dual scale; 65-89=master/slave protocol
address

3.1

Timeout control.

0=NO 1=YES

3.2

Handshake.

0=NO 1=YES

3.3

Operator disable.

0=NO 1=YES

3.4

Host enquiry.

0=NO 1=YES

3.5

Remote keyboard commands.

0=NO 1=YES

3.6

Continuous weight output format

LEO or AND

3.7

(Reserved for future use)

3.8

Debug.

0=NO 1=YES

3.b

Baud rate serial number 2.

24 = 2400 bps
96 = 9600 bps
19 = 19200 bps
38 = 38400 bps
57 = 57600 bps

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 34 / 84

Search results

Summary of Contents for VT 200

Reviews: