Vishay VT 200 Technical Manual Download Page 31

Page: 31 / 84

Display, Keys and Menus

Setup Menus

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

Function Description

Refer to

Analog output test

Chapter 8

ROM - RAM test

. A validity check is performed on system ROM and RAM.

Chapter 8

Display segment test

. All digits go through 0-9 display routine in

sequence, after which the character set is displayed.

Chapter 8

Keyboard test.

Display blanks. The scan code of any key pressed is shown

on the display.

Chapter 8

Setpoint input/output test

. The display shows the status of the digital

input and outputs.

Chapter 8

Print buffer test

. An ASCII file (30h-7Fh) is output to the printer port with

error control.

Chapter 8

Display characters received by COM ports

. Any character received by

COM 1 is echoed and displayed in ASCII hex on digits 1 and 2. Any
character received by COM 2 is echoed and displayed in ASCII hex on digits
5 and 6.

Chapter 8

3.4 Setup

Menus

3.4.1

Accessing and Navigating Setup Menus

To enter the setup and calibration menus, either execute function 49, or follow the
procedure below.

To enter the setup and calibration menus:

Turn on the unit.

During the self-test routine, while all display segments are on (all 8 on the

display), press

PRINT

( ) momentarily, followed by

TARE

( ) momentarily.

3. If the PIN code is activated, the display shows

ACCESS

briefly. Type the PIN and

then press

PRINT

( ) to get into the calibration menu. The display shows

SETUP

4. Use

TOTAL

(

) to step through the menus.

The menus displayed depend on whether jumper JP1 is in the sealed position or

not (see section

4.4). If it is sealed, the following menus are hidden:

Par

CAL

INIT

and

A-CAL

5. To enter a menu, press

PRINT

( ).

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 31 / 84

Search results

Summary of Contents for VT 200

Reviews: