Vishay VT 200 Technical Manual Download Page 49

Page: 49 / 84

Serial Communication

Serial Ports Configuration

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

6 Serial

Communication

Communication and printer parameters can be set in the

SETUP 2

and

SETUP 3

submenus of the

SETUP

menu.

6.1 Serial

Ports

Configuration

VT200/220 has two serial ports, designated port 1 and port 2:

Port 1 is an RS232 port.

Port 2 is an optional port installed on order, and can be either RS232 or RS485.

6.1.1

RS232 Serial Port

The port is used to connect to serial printers or personal computers.

General

Asynchronous serial ASCII, RS232C standard, full duplex.

Protocol

1200, 2400, 4800 or 9600 baud rate, 1 start bit, 8 data bits/no parity or 7 data bits/odd
or even parity, 1 stop bit.

Handshake

DTR BUSY per character for fanfold printers or REQUEST PAPER END STATUS for EPSON
TM-295 slip printer.

Connection

Cable gland, stainless steel enclosure or DB9 male on rear panel, aluminum enclosure
(J1 or J3). Three-conductor shielded cable, max distance 15m.

Tx = Pin 3

Rx/DTR = Pin 2

GND = Pin 5

6.1.2

RS485 Serial Port

Used to connect to a host computer, remote printer, remote display, etc.

General

Asynchronous serial ASCII, RS485 half duplex.

Protocol

2400 to 57600 baud, 1 start bit, 8 data bits/even or no parity 7 data bits/even parity, 1
stop bit.

Connection

Cable gland, stainless steel enclosure or DB9 female on rear panel aluminum enclosure
(J3). Two-conductor twisted-pair shielded cable, max distance 1000m. A termination
resistor (120R) may be connected by shorting pins 8 and 9.

A = Pin 6

B = Pin 7

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 49 / 84

Search results

Summary of Contents for VT 200

Reviews: