manualshive.com logo in svg

Vishay VT 200, Technical Manual, Page: 7 / 84

Share
Download
Vishay VT 200 Technical Manual Download Page 7

 

 

Legal Notice 

 

 

 

VT200/220 Technical Manual, Rev 1.00.01 

vii

 Doc 

# 

TM-VT200/220-EN

 

Legal Notice 

This manual contains information that is proprietary to Vishay Transducers Ltd. 
(“VT”).  No part of this publication may be reproduced in any form whatsoever 
without prior written approval by VT. 

Right,  title  and  interest,  all  information, copyrights,  patents,  know-how,  trade  
secrets  and  other intellectual property or other proprietary rights relating to this 
manual and to the VT200 and/or VT220 (“the Product”), and any software 
components contained therein, are proprietary products of VT protected under 
international copyright law and shall be and remain solely with VT. 

VT200 and VT220 are registered trademarks of VT. No right, license, or interest to 
such trademark is granted hereunder, and you agree that no such right, license, or 
interest shall be asserted by you with respect to such trademark. 

You shall not copy, reverse compile or reverse assemble all or any portion of the 
Manual or the Product. You are prohibited from, and shall not, directly or indirectly, 
develop, market, distribute, license, or sell any product that supports substantially 
similar functionality as the Product, based on or derived in any way from the 
Product. Your undertaking in this paragraph shall survive the termination of this 
Agreement. 

This Agreement is effective upon your opening of the packaging of the Product, 
and shall continue until terminated. VT may terminate this Agreement upon the 
breach by you of any term hereof. Upon such termination by VT, you agree to 
return to VT the Product and all copies and portions thereof. For further 
information contact VT or your local distributor. 

Summary of Contents for VT 200





















































































Reviews:

No comments