Vishay VT 200 Technical Manual Download Page 14

Page: 14 / 84

Technical Specifications

General

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

1 Technical

Specifications

1.1 General

CPU Characteristics

MCU 89C51RD, 64KB Flash ROM, 1KB RAM, 32KB serial EEPROM.

CPU real time clock is optional.

Communication

•

Serial port 1: RS232C Full duplex, 1200-9600 baud rate,

8 data bits/no parity

or 7 data bits/odd or even parity. Printer, weight output.

•

Serial port 2: (optional): RS232 or RS485 half duplex, 2400-57600 baud rate,
8 data bits/even or no parity or 7 data bits/even parity.

Master/slave protocol, EDP output, selectable weight output.

Display

•

VT200: 6 digit ,7 segment red LED (20mm height) display.

•

VT220: Black LCD (16mm height) display.

Annunciators

Net, No Motion, Minus sign, Zero, Range 1 and 2.

Keyboard

8-key membrane type with tactile feedback.

Approvals

EU type approval 10,000 divisions, DK 0199.62.

Accuracy class

III.

Resolution

Selectable up to 99,000 dd (in accordance with regulations).

Max tare effect

Full scale (100%).

Auto Zero track

Off or 0.5 dd, setup-selectable.

Weight digits

4, 5 or 6.

Weight steps

1, 2, 5, 10, 20, 50, 100, 200.

Digital filter

FIR automatically adjusted to conversion speed, plus post filtering (rolling
average of 1, 2, 4, 8, 16, 32 samples).

Calibration methods

Dead load, span and scale parameters via keyboard commands. Calibration can
be performed either by weighing or by entering load cell mV values.

Self diagnostics

Hardware and software – MCU watchdog.
Memory failure and I/O failure – program check.

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 14 / 84

Search results

Summary of Contents for VT 200

Reviews: