manualshive.com logo in svg

Vishay VT 200, Technical Manual, Page: 23 / 84

Share
Download
Vishay VT 200 Technical Manual Download Page 23

 

 

Display, Keys and Menus 

The Display 

 

 

VT200/220 Technical Manual, Rev 1.00.01 

23

 Doc 

# 

TM-VT200/220-EN

 

3  Display, Keys and Menus 

  

 

The VT200/220 front panel can be divided into three areas: 

 

 

A six-digit display (LED for VT200, LCD for VT220) that shows weight 
information, status information, and the names of menus and functions. 

 

 

A keypad with eight keys, allows you to turn the unit on and off, perform the 
most common functions, and access a function menu with more advanced 
options.  

 

 

The lower area shows information about the maker, model and certified limits of 
your indicator.  

3.1 The 

Display 

The VT200 has an LED display, while VT220 model has an LCD display. Both models 
have six digits, used mainly to display weight information.  

To the bottom and right of the digits, small dots may appear next to distinctly-shaped 

status annunciators

. These dots provide status information, such as whether the scale 

has been tared or not. 

Summary of Contents for VT 200





















































































Reviews:

No comments