manualshive.com logo in svg

Vishay VT 200, Technical Manual, Page: 60 / 84

Share
Download
Vishay VT 200 Technical Manual Download Page 60

Serial Communication 

Standard Print Formats 

 

 

VT200/220 Technical Manual, Rev 1.00.01 

60

 Doc 

# 

TM-VT200/220-EN

 

6.4 Standard 

Print 

Formats 

You can select one of the ten VT200/220’s standard print formats, shown and 
explained in the table below, using the function menu (functions 21 through 30). 
Executing the function that corresponds to a print format makes it the current print 
format. This is the format used by the printer when users press 

PRINT

 

( ). 

  It is also possible to download one of two custom print formats  

(see section 6.5). 

 

Func.   Name of  

Print Format 

Contents  

(in this order)

 

Layout 

21 

Ticket 

Date, time, weight.  
Whether a gross or net 
weight is shown depends 
on the current VT200/220 
mode. 

 

 29-04-03   09:15    N:0010 

WEIGHT : <123.40 kg> 

     

22 

Continuous output 

Sends the current weight measurement and status to an external device (a 
display or PC). Layout depends on the settings of the external device. 
There are 2 Continuous output  formats LEA and AND see 6.3.2 

23 

Net/gross 

Either net or gross 
weight, depending what is 
shown on the display. 

 

GROSS : <05210kg> 

 

OR 

 

NET : <00950 kg> 

         

24 3-line 

detailed 

weight 

When net weight is 
showing: Gross weight, 
tare value and net 
weight.  

When gross weight is 
showing: Gross only. 

 

GROSS : 07940kg 

TARE  : 06170kg 

NET   : 01770kg 

     

OR 

 

GROSS : <06170kg> 

         

25 3-line 

detailed 

weight large 

Gross weight, tare value 
and net weight in large 
characters. 

 

GROSS : 07940kg 
TARE  : 06170kg 
NET   : 01770kg 

             

Summary of Contents for VT 200





















































































Reviews:

No comments