Vishay VT 200 Technical Manual Download Page 28

Page: 28 / 84

Display, Keys and Menus

The Function Menu

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

Function Description

Refer to

Set date, time and serial number.

A battery-backed RAM and the Real

Time Clock (RTC) option need to be installed to enable setting time.

This function depends on the setup parameter

1.6

(1=enabled; 0=disabled).

The date format is specified in setup parameter

1.4

(

DDMMYY

MMDDYY).

Use

(

P.TARE

) to change the current digit, then

(

TARE

) to move to the

next digit. When you are done, press

(

PRINT

The display now shows

HHmmSS

(hours, minutes, seconds); edit the current

time and confirm.

The display shows the current alibi memory serial number, also used on the
printed ticket. You can edit this number, then press

(

PRINT

High resolution weighing.

Increases the accuracy of the displayed weight

by a factor of ten, the smallest item is limited to 1 display division.

When this function is enabled, the display flashes and you may not print.

Press

ZERO

(

) to cancel and return to normal resolution.

User’s Guide,
section 4.6

Disable printer output.

Prevents the indicator from printing when you

press

PRINT

(

), even if a printer is connected.

Set print format: Ticket.

Shows date, time and weight, as follows:

07-10-02 00:00:00 N:00001

GROSS:<00.500 kg>

Section 6.4

Set print format: Continuous output.

Used for external display or PC.

There are 2 continuous output formats LEO and AND see 6.3.2

Section 6.4

Set print format: Net/gross.

Shows either net

gross weight,

depending what is shown on the display.

Gross weight:

GROSS: <00.500 kg>

Net weight:

NET: <01.000 kg>

Section 6.4

Set print format: 3-line detailed weight.

Shows gross, tare and net

weight in three separate lines as follows:

GROSS : 01.100 kg

TARE : 00.100 kg

NET : <01.000 kg>

Section 6.4

Set print format: 3-line detailed weight large.

Same as function 24,

except the information is printed in quadruple-size characters.

Section 6.4

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 28 / 84

Search results

Summary of Contents for VT 200

Reviews: