Vishay VT 200 Technical Manual Download Page 29

Page: 29 / 84

Display, Keys and Menus

The Function Menu

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

Function Description

Refer to

Set print format: 1-line detailed weight.

Shows serial number, gross,

tare and net in one line as follows:

00002 01.100kgG 00.100kgT 01.000kgN

Section 6.4

Set print format: Displayed weight.

The weight is shown on the display

(regardless of mode).

Section 6.4

Set print format: 1-line weight and serial

00001 00.500 kg

Section 6.4

Set print format: On demand.

Weight data (either net or gross,

depending what is shown on the display) is transmitted every time a
character (set in setup parameter

3.t

) is received from a connected

peripheral. The format is as follows:

Gross weight:

GROSS:<00.500 kg>

Net weight:

NET:<01.000 kg>

Section 6.4

Set print format: Label.

Prints a label showing gross weight, tare and net

weight. The format is as follows:

GROSS TARE NET

00.500kg 00.100kg 01.000kg

Section 6.4

Changing PIN.

Used to change the current Personal Identification Number

that enables access to the calibration procedure.

Chapter 8

Download custom print format 1.

Downloads a custom print format from

a PC. Suitable for operations in gross mode.

Section 6.5.1

Download custom print format 2.

Downloads a custom print format from

a PC. Suitable for operations in Tare mode.

Section 6.5.2

Repeat last printout.

Prints an exact copy of the last printout.

User’s Guide,
section 6.1.1

Check calibration seal.

Shows the calibration counter, and the status of

the physical calibration seal (if used).

Setup and calibration

Chapter 4

Piece count.

Switches between Counting Mode and Weighing Mode. Same

as pressing

Pcs

(

User’s Guide,
chapter 5

Set unit weight for counting, by weighing.

The display shows

. Enter

the number of units currently on the scale and press

PRINT

(

). The

indicator records the average unit weight and uses it for counting.

User’s Guide,
section 5.2

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 29 / 84

Search results

Summary of Contents for VT 200

Reviews: