Vishay VT 200 Technical Manual Download Page 69

Page: 69 / 84

Outputs and Digital Input

Configuring Analog Output

VT200/220 Technical Manual, Rev 1.00.01

Doc

TM-VT200/220-EN

Par. Description

Values

A.3

Error output level

. Specifies whether scale errors should be

indicated as a low or high signal.

0 = Low (0mA)

1 = High (24mA)

A.4

Current / voltage

. This parameter must correspond to the

hardware jumper, which defines whether output should be in
current or voltage (see section

7.4.1).

0 = Current

1 = Voltage

A.5

Net / gross

. Specifies whether the indicator should always

output gross weight, or output net weight when tare is active.

0 = Net weight

1 = Gross weight

A.6

Effective Range for current output

. Sets the range to 0-

20mA or 4-20mA. Relevant only if A.4 and the hardware
jumper are set to current.

0 = 0-20mA

1 = 4-20mA

A.7

Resolution

. Specifies whether output should be in high

resolution if the display is showing high resolution.

0 = Display

1 = Internal

A.8

Operation

. Enables and disables the analog output.

0 = Disabled

1 = Enabled

7.4.3

Calibrating D/A Converter

To calibrate D/A converter (0-10V):

1. Place jumper JP1 on PCB (761) for voltage output.
2. Power up the unit, enter the setup menus and enter the

ACAL

menu.

3. Set parameters as follows:

A.1

=1;

A.2

=0;

A.3

=0;

A.4

=1;

A.5

=0;

A.6

=0;

A.7

=1;

A.8

=1.

4. Skip D/A calibration and save the above settings by selecting

STORE

Access the function menu and select function 85 (see 3.3.1).

The display shows

C 00000

. Enter 65535. Press

PRINT

to output the value.

Use a voltmeter to measure the voltage at pins 2 (+) and 3 (-) of the analog

output connector (J4). Record the value (in volts). Calculate a new value, which is:

100/recorded value. E.g. Recorded value is 9.94, new value is 100/9.94=10.06.

This is the

full scale voltage.

Exit Fn 85 and re-enter the

ACAL

menu.

9. Set parameter

A.1

to 1. The calibration dialog starts.

10. When prompted for D/A Zero, enter 00.000.
11. When prompted for D/A Span, enter the

full scale voltage

you calculated in step 7.

12. When you finish stepping through the dialog, exit the

ACAL

menu.

13. Select

STORE

to save your settings.

Summary of Contents for VT 200





















































































Search results

Summary of Contents for VT 200

Reviews:

Vishay VT 200, Technical Manual, Page: 69 / 84

Search results

Summary of Contents for VT 200

Reviews: