manualshive.com logo in svg

Vishay VT 200, Technical Manual, Page: 35 / 84

Share
Download
Vishay VT 200 Technical Manual Download Page 35

 

 

Display, Keys and Menus 

Setup Menus 

 

 

VT200/220 Technical Manual, Rev 1.00.01 

35

 Doc 

# 

TM-VT200/220-EN

 

3.d 

Data bits serial channel 2. 

17 = 7 data bits / even parity 
08 = 8 data bits / no parity 
18 = 8 data bits / even parity 

    SETUP > SETUP 4 (Tilt Switch) 

Par. Description 

Values 

4.t 

Time delay, after closing the contact, for the display to lock. This is 
also the time for the display to unlock after the contact is opened. 

This parameter allows several special options, accessed by setting it 
above 

90

: 

•

 

91

 – Tare scale on the rising edge of input. Setpoints always 

enabled.  

•

 

92

 – Print on the rising edge of the input. Setpoints always 

enabled. 

•

 

93

 – Setpoints active when input is high. Setpoints inactive when 

input is low. 

•

 

94

 – Scale is tared at the rising edge of input. If taring is 

successful, setpoints are activated. If input is low, setpoints are 
inactive. 

•

 

95

 – When input is low, scale 1 is selected and displayed. When 

input is high, scale 2 is selected and displayed. 

•

 

96 – Scale is zeroed. 

00=disabled 

01-90 (x o.1 sec)  

91-96=special options 

   SETUP > SETUP 5 (Setpoints) 

Par.  

Description 

Values 

5.1, 5.2 

Setpoint 1 output. 

5.1=0 and 5.2=0: normal 

5.1=1 and 5.2=0: no motion 

5.1=0 and 5.2=1: error 

5.3, 5.4 

Setpoint 2 output. 

5.3=0 and 5.4=0: normal 

5.3=1 and 5.4=0: zero 

5.3=0 and 5.4=1: net 

5.6 

Net / gross

 

for both setpoints.

 

0 = net   

1 = gross 

5.7 

Normally open / closed for both setpoints.

 

0 = normally open   

1 = normally closed 

Summary of Contents for VT 200





















































































Reviews:

No comments