manualshive.com logo in svg

Vishay VT 200, Technical Manual, Page: 12 / 84

Share
Download
Vishay VT 200 Technical Manual Download Page 12

About this Document 

 

 

 

VT200/220 Technical Manual, Rev 1.00.01 

xii

 Doc 

# 

TM-VT200/220-EN

 

About this Document 

This document provides technical information for the VT200/220 Weight Indicator. 
It is intended for technical staff tasked with installing, setting up and configuring 
the indicator, as well as troubleshooting and servicing.  

For information on how to use the products, see the 

VT200/220 User’s Guide

.  

Chapters and Their Contents  

 

1 Technical 

Specifications     

General indicator specifications; analog input/output 
specs; and digital input/output specs. 

Pg. 13 

2 Installation 

Installing and connecting the indicator. 

Pg. 16 

3 

Display, Keys and 
Menus 

Using the VT200/220 display, keypad, function menu 
and setup menus. 

Pg. 20 

4 Calibration 

Performing standard weight calibration and electronic 
calibration.  

Pg. 28 

5 Setting 

Operating 

Parameters 

General parameters in the 

SETUP 1

 and 

PAR

 menus. 

Pg. 33 

6 

Setting up Serial 
Communication 

Setting up communication with printers, host PCs and 
other external devices.   

Pg. 38 

7 

Outputs and Digital 
Input 

Connecting and using the digital input (tilt switch), 
digital outputs (setpoints) and analog output. 

Pg. 45 

8 Service 

Operations 

 

and Testing 

How to set a PIN number, set date and time, view load 
cell mV, test the keypad and display, and perform 
other service and testing operations. 

Pg. 47 

9 Troubleshooting 

and 

Service 

Errors, causes and suggested corrective actions; 
maintenance and service instructions. 

Pg. 50 

 

Summary of Contents for VT 200





















































































Reviews:

No comments