US Robotics Courier USR3510 User Manual Download Page 91 | Manualshive

Page: 91 / 162

background image

Revision: 1.00

Copyright 2015 U.S. Robotics Corporation

91 |

P a g e

Diversity WWAN Antenna

The diversity antenna is labelled

WWAN Div GPS

on the front panel.

Learn about antenna

recommendations.

Connectors



Uses the same type of connector as the main WWAN antenna

Frequency range



Receive diversity only works on WCDMA and CDMA bands



Only WCDMA and CDMA bands have to be supported by the diversity antenna.



The GPS frequency must also be supported if GPS functionality is desired on the gateway.

Efficiency



Radiation pattern: Omni-directional



Efficiency over all used frequencies: > 25%



Maximum VSWR: < 2.5:1 with 50 ohm reference impedance

Polarization



Linear

Mutual coupling

(main antenna and diversity antenna)



Isolation: > 8dB



Envelope correlation coefficient: < 0.5

GPS Antenna

The gateway only supports passive GPS antennas. There is no power supply for active antennas on the
RF connector. For accurate GPS operation make sure the GPS antenna has a clear view of the sky.

RF EXPOSURE WARNING

To comply with FCC and Industry Canada regulations limiting both maximum RF output
and human exposure to RF radiation, maximum antenna gain must not exceed:

  Cellular (800MHz) band < 4 dBi
  PCS (1900MHz) band < 3.5 dBi
  AWS (1700MHz) band < 3.5 dBi

To comply with the CE regulations, maximum antenna gain must not exceed the antenna
gain of the Taoglas TG.09.0113 antenna.

IMPORTANT: The diversity antenna is by default disabled (from firmware version 1.9.0 onwards).

Learn how to enable the diversity antenna

.

«
...
89
90
91
92
93
...
»

Summary of Contents for Courier USR3510



































































































































































Reviews:

No comments

Related manuals for Courier USR3510

Brand: Quintum Pages: 4

Q gateway 5.5 direct

Brand: QUNDIS Pages: 80

Brand: Ursalink Pages: 23

Brand: RTA Pages: 73

Brand: Digi Pages: 6

Brand: Samsara Pages: 15

Brand: Wiznet Pages: 53

Brand: Honeywell Pages: 60

Brand: Honeywell Pages: 134

RB924i-2nD-BT5&BG77

Brand: MikroTik Pages: 16

Brand: ICP DAS USA Pages: 122

SIMATIC IOT2020

Brand: Siemens Pages: 2

SIMATIC IOT Gateway MQTT

Brand: Siemens Pages: 2

MindConnect Nano

Brand: Siemens Pages: 2

Instabus/DALI Gateway N 141

Brand: Siemens Pages: 5

SIMATIC IOT2050

Brand: Siemens Pages: 25

GAMMA 5WG1 143-1AB01

Brand: Siemens Pages: 2

Brand: Siemens Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands