US Robotics Courier USR3510 User Manual Download Page 17

Page: 17 / 162

Revision: 1.00

17 |

P a g e

Slide the card into slot, using the side channels or grooves on the housing to guide the card into
place. Make sure the screw holes line up.

Push gently until the card is flush with the housing.

Secure the card with the screws.

The following table lists the expansion cards available from Option and the slot.

Expansion Card

Slot

Wi-Fi Card (CG2101)

Back

Low Cost Serial Card (CG1101)

Front

Industrial Serial Card (CG1102)

Front

Basic Ethernet Switch (CG1104)

Front

PoE Ethernet Switch (CG1103)

Front

Developers Card (CG1105)

Front

Removing Expansion Cards

Remove the Torx screws that fasten the card to the base unit.

Plug a connector into the mating connector on the expansion card. If the card has multiple
connectors, choose a connector near the right edge.

Remove the expansion card by pulling the plug or cable that is inserted into an expansion card
connector.

Note:

The expansion card faceplate will deform if the card is pulled at the edge.

Do not attempt to remove the expansion card by pulling its edge!

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands