US Robotics Courier USR3510 User Manual Download Page 69

Page: 69 / 162

Revision: 1.00

69 |

P a g e

IP Config



Displays the IP, netmask and gateway addresses of the connected WLAN network.

Available & Known networks



Lists the WLAN networks within range and displays the signal quality, SSID, status, and encryption
method of each.



Click the Refresh icon to refresh the network list.

Connecting to a WLAN Network

To connect to a WLAN network:

Click the network name.

Enter the network password and click

Connect

Note the status change to connected in the Available & Known Networks list.

Creating a Manual Connection to a WLAN Network

If the WLAN network you want to use is not in the list of known networks, you can create a manual
connection.

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands