US Robotics Courier USR3510 User Manual Download Page 125

Page: 125 / 162

Revision: 1.00

125 |

P a g e

Then you see all the software that is currently set for this group. For example, to change the application
click 'Choose a different application'.

Now you can choose any of the applications that are made available for this group.

Devices

The main function of the USR Universe is to provide an easy-to-use mechanism for updating Gateway
devices before and after deployment in the field.

You can do the following tasks:



Sort and select devices by serial number and other criteria so that you can quickly find
the devices you need to update



Edit device name and description if necessary

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands