US Robotics Courier USR3510 User Manual Download Page 8

Page: 8 / 162

Revision: 1.00

8 |

P a g e

PoE Ethernet Switch - CG1103



Power over Ethernet board. (requires special power supply)



4-port 10/100Base-T with 2 ports class 4 or 4 ports up to class 3 PoE



µSD card

Developers Expansion Card - CG1105



Extended format with headers on all interfaces to attach to development equipment



Pre-wired RS-232 port, GPIO connected temperature sensor, a relay and SD card slot.

Related Topics

Installing Expansion Cards

Configuring Expansion Cards

USR Universe

The USR Universe is the configuration and deployment mechanism for the USR Gateway. From the
factory, the base unit is pre-configured for a USR3516-EMU Modemulator card.

power-up

, the gateway connects to the USR Universe over the wired Ethernet port and automatically

downloads the appropriate update. If the Ethernet interface is unavailable, then the gateway uses the

WWAN interface

to download the updates.

The Gateway downloads the following files from the USR Universe:



Gateway firmware: System firmware provided by USRobotics.



Gateway developer image: customized software that provides additional functionality to the
gateway or controls third-party expansion cards.



Gateway config file: configuration settings that can be applied to one or more gateways



Gateway GOBI firmware image: software that updates changes to wireless operator firmware

Related Topics

USR Universe Guide

3G Connection Tab

Tip:

You can set the USR Universe to enable or disable the automatic downloads.

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands