US Robotics Courier USR3510 User Manual Download Page 113 | Manualshive

Page: 113 / 162

background image

Revision: 1.00

Copyright 2015 U.S. Robotics Corporation

113 |

P a g e

Activating a Gateway Using USR Universe



Before being able to activate a device, you need to have already created a group (including
correct device type).



You can activate a Gateway two ways:

1.

Activate a single device

2.

Activate devices in bulk

Activation of a single device



From the ‘Device’ section please click the ‘Activate new device’.



Then fill in the Serial and activation code for this device and choose which group it should
belong to (mandatory). It is also possible to add a friendly name for the device (optional). If no
name is chosen the serial number will be used.



When the Gateway device is powered up, it will check-in to USR Universe. USR Universe will
then enable this device and it will be activated and visible in the group view.



The Gateway will download the group setting (or custom setting), if they differ from what is
currently deployed.

«
...
111
112
113
114
115
...
»

Summary of Contents for Courier USR3510



































































































































































Reviews:

No comments

Related manuals for Courier USR3510

Brand: ABB Pages: 4

NETWORK INTERFACE CARDS

Brand: Secure Computing Pages: 17

Brand: Net2Phone Pages: 23

Brand: King Pigeon Pages: 58

Brand: Gree Pages: 31

Brand: CSM Pages: 40

Brand: VOPtel Pages: 38

Brand: Hitron Pages: 2

Kona Mega Gateway

Brand: TEKTELIC Communications Pages: 16

Kona Macro Gateway

Brand: TEKTELIC Communications Pages: 32

Brand: Avaya Pages: 254

Brand: ICP DAS USA Pages: 37

Brand: Innovaphone Pages: 155

Brand: olympia electronics Pages: 4

Brand: Ember Pages: 24

Brand: ZKTeco Pages: 2

Brand: ABB Pages: 11

Brand: Rotronic Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands