US Robotics Courier USR3510 User Manual Download Page 55

Page: 55 / 162

Revision: 1.00

55 |

P a g e

Plugin Tab

The Plugin tab configures the serial port settings and the GPS settings.

It includes the following sections:



Serial Port to TCP local or remote server



Serial port settings



TCP settings



GPS to TCP local or TCP/UDP remote server



GPS report settings



TCP/UDP selection



TCP settings



UDP settings

Serial Port to TCP local or remote server

Enable



This parameter enables (Yes) or disables (No) the serial port and presents the serial port settings
menu.

NOTE:

This tab is active only when the Modemulator is in gateway mode. These settings are

ignored when the Modemulator is in Modemulator mode.

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands