US Robotics Courier USR3510 User Manual Download Page 53

Page: 53 / 162

Revision: 1.00

53 |

P a g e

Config Export

Download config



Click to save the device configuration to a file on a laptop. The configuration file can then be
uploaded to the Provisioning Server and used for provisioning multiple devices.

System Reboot and Factory Reset

Two different manual resets are possible on the gateway: system reboot and factory reset.

System reboot

To reboot the gateway:

Click

System reboot

In the confirmation dialog box, click

Reboot

to confirm.

TIP:

Automatic resets of the WWAN interface are managed by the

connection watchdog

feature.

Automatic resets of the gateway are managed by the

timed reset

feature.

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands