US Robotics Courier USR3510 User Manual Download Page 46

Page: 46 / 162

Revision: 1.00

46 |

P a g e



Set to

Monthly

and enter the day of the month and the time of the day.

Provisioning Tab

The Provisioning tab configures how and when the gateway checks for updates from the USR Universe.

By default, the gateway base unit connects to the USR Universe each time the device is powered on, and
checks for an updated image. The device downloads and installs the update over the WAN interface.

Check for Updates

Check for updates



Checks the USR Universe for firmware, developer image, and configuration file updates



Click the

Check for Updates

button to check for updates even if

Enable automatic provisioning

disabled.

Upload Device Provisioning File

Select file



Updates the unit with an image from a hard drive.



Click

Browse

to select the file and then click

Upload

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands