US Robotics Courier USR3510 User Manual Download Page 42

Page: 42 / 162

Revision: 1.00

42 |

P a g e

Outbound Trusted IPs

The Outbound Trusted IPs section defines IP addresses that can be contacted when LAN-to-WAN traffic
is not allowed.

Outbound Trusted IPs



When the LAN to WAN traffic is rejected or dropped based on the default firewall policies, no data
can be transmitted from the LAN to the WAN network.



The outbound trusted IP list defines the IP addresses that can be contacted even when LAN-to-WAN
traffic is not allowed.



Enter an IP address and click

Add

Static Routing

Static routing allows you to define a specific gateway for an IP address



Interface: Specify on which interface you would like to have the static routing



Target: Specify the destination IP address.



Netmask: Specify the netmask of the destination IP address



Gateway: Specify the gateway which has to be used to send packets to the target IP address.

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands