US Robotics Courier USR3510 User Manual Download Page 116 | Manualshive

Page: 116 / 162

background image

Revision: 1.00

Copyright 2015 U.S. Robotics Corporation

116 |

P a g e



The user can then start to edit the group, adding devices, invite owners and members

Adding device(s) to a group



There are 3 possible ways to add a device or devices to a group:

1.

Activate a single device

2.

Activate devices in bulk

3.

Move from another group

Adding a single device



From the ‘Device’ section please click the ‘Activate new device’.



Then fill in the Serial and activation code for this device and choose which group it should
belong to (mandatory). Also possible to add a friendly name for the device (optional). If no name
is chosen the serial number will be used.



When the Gateway device is powered up, it will check-in to USR Universe. USR Universe will
then enable this device and it will be activated and visible in the group view.

«
...
114
115
116
117
118
...
»

Summary of Contents for Courier USR3510



































































































































































Reviews:

No comments

Related manuals for Courier USR3510

Brand: ABB Pages: 2

Brand: RTA Pages: 72

Brand: B&B Electronics Pages: 68

NIOT-E-TPI51-EN-RE

Brand: hilscher Pages: 258

Brand: Moeller Pages: 78

SBG3500-N Series

Brand: ZyXEL Communications Pages: 10

Brand: Grandstream Networks Pages: 20

Brand: turck Pages: 11

Brand: Luminext Pages: 8

Brand: Authonet Pages: 2

Brand: Voptel Technology Pages: 67

Brand: Packet Media Pages: 7

Brand: Watchguard Pages: 18

TotalStorage NAS Gateway 300

Brand: IBM Pages: 14

Brand: D-Link Pages: 75

ESPRESSObin Ultra

Brand: GlobalScale Pages: 24

Brand: RTA Pages: 71

Brand: OpenVox Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands