US Robotics Courier USR3510 User Manual Download Page 142

Page: 142 / 162

Revision: 1.00

142 |

P a g e

Click the ‘Checkbox’ to the user(s) that should be removed

Then click ‘Remove from Group’

Then a confirmation box appears showing that the chosen user(s) has been removed from
the group.

Managing Software

The USR Universe allows you to manage the firmware and software images for the Gateway base unit.
Each image can have multiple releases.

You can perform the following tasks:



Manage Gateway firmware provided by USRobotics



Manage Gateway radio firmware for the radio module



Manage Gateway configurations from a locally configured device



Manage Gateway applications for controlling third party expansion cards or software

Radio firmware can be changed only on the USR3520. Radio firmware cannot be changed on the

USR803520.

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands