US Robotics Courier USR3510 User Manual Download Page 25

Page: 25 / 162

Revision: 1.00

25 |

P a g e

Mode



This will define the state of the Ethernet interface when the WAN/LAN Switchover feature is
disabled.



When the WAN/LAN switchover feature is enabled the state of the Ethernet interface will be as
in the following table:

Result of WAN/LAN switchover feature

State of "Mode"

End result

WAN

LAN

WAN

LAN

WAN

WAN/LAN Switchover



The WAN/LAN switchover feature defines the state of the Ethernet port after the gateway is
powered on. By default,

WAN/LAN Switchover

is enabled.

Learn more about the WAN/LAN

switchover feature



If set to

Yes

the gateway tries to connect to the Internet through the Ethernet connection, such

as an ADSL or cable modem. If a connection is unavailable, the port switches to LAN mode and
acts as a LAN interface.



Set to

to power on the Ethernet port as defined in the

"mode"

parameter.

MTU



The

MTU packet size

: Value range 68 to 1500

IP address



Sets the IP address of the gateway. By default the IP address is 192.168.1.1. You can change this
to any value you want.

Netmask



Sets the netmask of the gateway. By default the netmask is set to 255.255.255.0. You can
change this to any value you want.

Enable DHCP server



Enables the DHCP server. By default the DHCP server is enabled. (When the Ethernet port is in
LAN state). In case you want to use static IP addresses in your network you can disable the DHCP
server.

DHCP range



Sets the DHCP range for the DHCP server.

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands