US Robotics Courier USR3510 User Manual Download Page 151

Page: 151 / 162

Revision: 1.00

151 |

P a g e

Then you will see all the software that is currently set for this group. We now want to change the
application for this group. Go ahead and click 'Choose another application'

Now you can choose any of the applications that are made available for this group. In this example it is
the SensorMaster application.

To choose the 'SensorMaster' as the new default application for this group, click 'Select version' and you
will see the following screen:

Choose the version number you want to use and click 'Apply changes'

You have now successfully updated the application for this group and all the Gateway devices will
update to this application next time they check-in.

Summary of Contents for Courier USR3510





























































































































































Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands

US Robotics Courier USR3510, User Manual

Search results

Summary of Contents for Courier USR3510

Reviews:

Related manuals for Courier USR3510

Brands by name

Popular brands