UniPOS IFS7002 Instruction Manual Download Page 9

Page: 9 / 107

UniPOS

Interactive Fire ControlPanel IFS7002

Instruction Manual

Page

Revision 2.05

Of 107

4.5. Monitored outputs

−

Type

- potential

−

lectrical characteristics

- (24±5)V/100mA

4.6. Relay outputs for fire conditions

−

Type

- potential free, switching,

−

Electrical characteristics

- 3A/125VAC; 3A/30VDC

4.7. Relay output for fault conditions

−

Type

- potential free, switching

−

Electrical characteristics

- 3A/125VAC; 3A/30VDC

4.8. Performance

−

Control over fire alarm loops and monitored outputs for fault conditions (short circuit

and interruption) and automatic reset

−

Detection of removed devices in the loops and automatic reset

−

Ability to set the zones in Coincidence Mode

−

Two phases of Fire condition, programmable time for Fire condition stage I,

separately for each zone

−

Option to prolong the time period for Fire condition stage I with programmable

inspection period, specified for each zone

−

Built-in sounder for fire condition – one tonal, discontinuous, can be switched off

−

Built-in sounder for fault condition – one tonal, discontinuous, can be switched off

−

Built-in real time clock

−

Set of test modes and options for adjustment:

♦

Setting the clock;

♦

Check ups on light and sound indications;

♦

Test of fire alarm zones;

♦

Adjustment of outputs and integrated external devices;

♦

Programming of parameters and modes of operation;

♦

Remote programming of the parameters from distant operator control point;

−

Energy independent archive of registered events with the events type, date and hour

– up to 1023 events;

−

Interfaces for communication with external devices - CAN 2.0B and RS-232

(directly or via modem).

4.9. Indications of registered events

−

Light indication

- LED

−

Text messages

- LCD display,

320

240 points, backlit

−

Sound signaling

- built-in sounder

4.10. Power supply

4.10.1. Mains

−

voltage

- 220/230V

−

frequency

- 50Hz

4.10.2. Back up batteries

−

battery type

- lead, gel electrolyte

−

number of batteries

- 2 pcs

−

connection

- serial connection

−

nominal voltage of the back up battery

- 24V

−

nominal capacity C

18Ah

−

extreme discharge voltage

- 21V

−

charge voltage

- 28,2V

4.10.3. Consumption on back up batteries supply

−

at 24V

- < 250mA

−

at 26V

- < 240mA

Summary of Contents for IFS7002












































































































Search results

Summary of Contents for IFS7002

Reviews:

Related manuals for IFS7002

Brands by name

Popular brands

UniPOS IFS7002, Instruction Manual

Search results

Summary of Contents for IFS7002

Reviews:

Related manuals for IFS7002

Brands by name

Popular brands