Tomy FLS-1000 Operator'S Manual Download Page 7

Page: 7 / 64

ー 6 ー

WARNING

When disposing or transferring FLS-1000

or its parts, FLS-1000 or the parts must

be appropriately decontaminated before

shipping it in any of the following cases:

In cases where FLS-1000 or any parts of

FLS-1000 has been exposed to infectious

and hazardous or radioactive substances.

In cases where FLS-1000 or any parts of

FLS-1000 has any residue of blood or

other chemicals and has been identified as

hazardous.

When returning FLS-1000 or any parts of

FLS-1000 for replacement or repair, FLS-

1000 or the parts must be appropriately

decontaminated before shipping it in any

of the following cases:

In cases where FLS-1000 or any parts of

FLS-1000 has been exposed to infectious

and hazardous or radioactive substances.

In cases where FLS-1000 or any parts of

FLS-1000 has any residue of blood or

other chemicals and has been identified as

hazardous.

Do not place hands on the top plate.

Otherwise, fingers or hands may get caught

in the chamber lid, resulting in injury.

CAUTION

Allow sterilizing water to cool down

sufficiently before draining water from

the chamber.

Water in the chamber or the exhaust tank

may be very hot after the operation, causing

burns.

Be careful of steam coming out of the

steam exhaust vent and its surrounding

area during the operation.

Hot steam may cause burns.

Allow chamber to cool down sufficiently

before performing maintenance work.

Otherwise, high temperature inside the

chamber may cause burns.

Make sure that there is no foreign

material in and around the lid gasket.

Otherwise, steam leak may occur, resulting

in burns. If any abnormality is found,

please contact your dealer or our local

representative.

Do not attempt to touch the outer panel

of the FLS-1000 during or immediately

after the operation.

Failure to do so may cause burns.

Keep away from the FLS-1000 while it is

in operation.

Failure to do so may cause burns. Please

keep at least 50 cm away from all four

corners of the FLS-1000 while it is in

operation.

Do not attempt to touch the exhaust tank

during the operation.

Failure to do so may cause burns.

Do not put hands into the top edge of the

rear panel.

Otherwise, fingers or hands may get caught

in the hinge area of the lid, resulting in

injury.

Be careful of the chamber or its

surrounding area after the operation

because it is very hot.

Failure to do so may cause burns.

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands