Tomy FLS-1000 Operator'S Manual Download Page 34

Page: 34 / 64

ー 33 ー

Press the STERILIZE key.

The STERILIZE indicator lights up to indicate that

the sterilization course is selected, while all process

indicators on the work monitor light up green.

Press the temperature setting up and down arrow

keys to set the temperature for the sterilization

process.

Press the time setting up and down arrow keys to

set the time for the sterilization process.

Press the exhaust speed level setting up and down arrow keys to set the exhaust level for the

temperature and pressure falling process.

Press the cooling fan setting key to select the number of fans which operate during the

temperature and pressure falling and temperature falling processes.

To set the sterilization operating parameters

①

②

③

④

⑤

5-7. Setting Operating Parameters

※

To change the time display format, refer to “6-7. Setting the Time Display Format”.

※

The upper limit of the temperature setting range varies depending on the altitude level selected

at the time of installation of the autoclave.

Altitude level code

Altitude level

Sterilization process

Temp. setting range

Time setting range

Below 800m

105

〜

123℃

0 : 01

〜

9 : 59

(switchable:

〜

99 hours)

Above 800m

〜

below 1500m

105

〜

122℃

Above 1500m

〜

below 2000m

105

〜

121℃

Table. Altitude level code and the corresponding altitude level, temperature and time setting ranges in

sterilization process

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands