Tomy FLS-1000 Operator'S Manual Download Page 40

Page: 40 / 64

ー 39 ー

5-11. Draining the Sterilizing Water from the Chamber

CAUTION

Allow sterilizing water to cool down sufficiently before draining water

from the chamber.

●

Water in the chamber or the exhaust tank may be very hot after the operation,

causing burns.

①

②

③

④

⑤

⑥

⑦

⑧

⑨

LO W E R

U P P E R

Open the chamber lid.

Open the drain access cover.

Pull out the drain hose.

Place the drain container underneath the drain hose.

Open the drain cock by rotating it slowly and drain the

sterilizing water from the drain port. If the water drains very

slow or does not drain, the port may be clogged. Clean the drain

port with tools such as a wire to remove the clog.

After completely draining water from the chamber, close the

drain cock.

Place the drain hose back to its original position.

Close the drain access cover.

Close the chamber lid.

Open

Close

WARNING

Do not attempt to open the drain cock unless the pressure gauge reads

0MPa.

●

If the drain cock is opened when pressure still remains in the chamber, hot

water may spurt out, causing death, injury or serious accident.

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Related manuals for FLS-1000

Brands by name

Popular brands