Tomy FLS-1000 Operator'S Manual Download Page 50

Page: 50 / 64

ー 49 ー

Illumination of the exhaust tank displays levels of water inside and raises an alert when the

water reaches full level, thereby allowing easy monitoring of the water level in the exhaust tank.

The exhaust tank turns on blue when the autoclave operates a cycle with water levels in the

exhaust tank between adequate levels. It turns on red when the lid is opened after a full water

level has been detected in the exhaust tank. Drain the exhaust tank when it turns on red. The

illumination function for the exhaust tank can be turned on or off.

6-11. Exhaust Tank Illumination Function

To turn on or off the illumination function

Press the FUNCTION key while the IN PROGRESS

indicator is off. The time display flashes “F00”.

Press the time setting up and down arrow keys to

show “F13” in the time display. The temperature

display shows the code of the illumination

function.

Press the START key. The temperature display

starts to flash.

Press the temperature setting up and down arrow keys to select the desired code of the

illumination function.

①

②

③

④

Press and hold down the START key to finalize the setting.

The buzzer will sound in approximately 4 seconds and the display will return to normal

display.

⑤

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Code

Illumination function

Off

※

The factory default value is 1.

※

For draining the tank refer to “5-4. Checking the Water Level in the Exhaust Tank”.

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Summary of Contents for FLS-1000

































































Search results

Summary of Contents for FLS-1000

Reviews:

Brands by name

Popular brands

Tomy FLS-1000, Operator'S Manual

Search results

Summary of Contents for FLS-1000

Reviews:

Brands by name

Popular brands